Sizing, Weight and Measurement Information for the P.U.D. GP/Tugger and the VacuTrac

Sizes and weights are very individual choices. We do not suggest nor do we prescribe which specific size and weight will be best for you. Such choices are best left to you and your physician. 

We can, however, advise how to take a penile measurement and inform you as to the average weights (in relation to size) that have been purchased by our previous customers. 

Refer to the measurement chart below, where the yellow arrow represents your penis. These measurements may be helpful in ordering the appropriate sized P.U.D. or Vacu-Trac for yourself. Remember these measurements, or enter them in the fields below and print this page.

Then return to Order Form: U.S. Orders PUD or VacuTrac [ INTERNATIONAL Orders PUD or VacuTrac ]

NOTE: Only Measurement "A" is necessary for the PUD (Tugger or GP). Measurements B & C are for the VacuTrac.
After taking your measurements, please refer to the sections below titled Which PUD size? or Which VacuTrac size?

Converting English System to Metric System

PUD Tugger & GP Sizes

1-1/8 in. = 2.8 cm

1-1/4 in. = 3.2 cm

1-3/8 in. = 3.5 cm

VacuTrac Sizes

1-1/2 in. = 3.8 cm

1-3/4 in. = 4.4 cm

2 in. = 5.1 cm

Weight

1 oz = 28.35 grams

STEP ONE (PUD and VacuTrac):
For the PUD Tugger or GP: With a flaccid penis, measure across the penile head (left to right) at the midpoint of the penile head, between the tip and the corona where it flares out. Do this again with an erect penis. This is Measurement A, flaccid and erect. Use the larger of these two numbers and write it on paper, or enter it in the box below as Flaccid = "x" or Erect = "x" (where "x" is your measurement).
For the Vacu Trac: With a flaccid penis, measure penis circumference (around) at the widest part of the head, this is usually the corona, where it flares out. Do this again with an erect penis. This is Measurement A, flaccid and erect. Use the larger of these two numbers and write it on paper, or enter it in the box below as Flaccid = "x" or Erect = "x" (where "x" is your measurement).

Measurement A for PUD or VacuTrac is:

STEP TWO (VacuTrac only):
Measure penis circumference (around) at the widest part of mid-shaft. Measure again while erect. This is Measurement B-flaccid and B-erect. Write these on paper or enter them in the box below as F=x and E=x (where "x" is your measurement).

Measurement B for VacuTrac is:

STEP THREE (VacuTrac only):
Measure penis length from base (closest to your body) to tip. Measure while flaccid and again while erect. This is Measurement C-flaccid and C-erect. Write these on paper or enter them in the box below as F=x and E=x (where "x" is your measurement).

Measurement C for VacuTrac is:


Which P.U.D. Size?
 If (A) above was 1 1/4" or less, the average size purchased was MED (Tugger is 10 oz. weight. GP is 12 oz. weight).
 If (A) was from 1 3/8" to 1 1/2", the average size purchased was LRG (Tugger is 12 oz. weight. GP is 14 oz. weight).
 If (A) was over 1 1/2", the average size purchased was X-LRG (Tugger is 14 oz. weight. GP is 18 oz. weight).

Which VacuTrac Size?
1) Decide if Measurement A-erect or Measurement B-erect is the larger number.
2) Use the larger number and divide it by 3.1416
3) Compare the result of the above division to the three sizes of VacuTrac: 1-1/2 inch, 1-3/4 inch, and 2 inch
4) Choose the VacuTrac size that is closest to the result of the above division.
It's better to choose a VacuTrac that's slighter bigger than your measurement, rather than smaller. You don't want the VacuTrac to be too tight. as this may cut off circulation.

Return to Order Form: U.S. Orders PUD or VacuTrac [ INTERNATIONAL Orders PUD or VacuTrac ]